We’ve pretty much dealt with any issue you can think of when it comes to garage door repair. Some concerns continue to surprise us.
Consider the insect colony that has grown on the picture eye sensor or the tennis ball that has managed to knock the door totally off its track.
Although you may make it work yourself in some situations, there are also several reasons why garage door maintenance should be left to the experts.
Knowing what’s wrong with your garage door will help you figure out the treatment. Such as, whether it’s a problem you can fix yourself or whether you need to contact for help.
How to solve common garage door issues
Despite their convenience and popularity, garage doors can occasionally become a major source of aggravation. With that in mind, we’ve put together this helpful guide on troubleshooting automatic garage doors.
Check out our list of common garage door issues and how to fix them. So you can get back to enjoying the convenience of an automated garage door:
Transmitter batteries are dead
The photo-eye is out of line
Un-aligned track
Broken springs
Issues with limit setting
Something is blocking the door
Transmitter batteries are dead
Although it may seem self-evident, your garage door transmitters require power to operate. The transmitter will not be able to send a signal to your garage door to open if the batteries in the transmitter are dead.
Solution
First, check to see if the transmitter located on the garage’s interior wall still works to open the door when tapped. If so, your car’s transmitter probably just needs a new battery.
Whether you have more than one garage door car transmitter, the batteries in the others will almost probably need a replacement shortly. Assuming, they were almost certainly put in at the same time.
The photo-eye is out of line
Sometimes the garage door opens properly but does not attempt to close when pressing the remote.
If this happens, the first thing you should do is physically verify the photo-eyes.
These eyes might become dusty over time, obstructing the light from the beam. They also become misaligned, causing the eyes to not line up on both sides.
Solution
Because the photo-eye is constructed of glass, similar to a camera lens, you must be careful not to scratch or damage it when cleaning it. You’ll need a soft cloth and a mild, streak-free cleaner to clean it.
Wipe away any dirt or debris that has accumulated on the eye gently. Be careful not to oversaturate, since this may cause dirt to attach to the eye more quickly.
Un-aligned track
If your garage door track is out of alignment, it could be a major issue. The metal track on which your door runs must be properly positioned for it to move.
If there are gaps between the rollers and the rails, or if the rails themselves bend, you have a problem. The heavy weight of the door can compound these issues to the point that operating it becomes risky.
Solution
Loosen the screws that hold the track to the frame before realigning it. Then, using a rubber mallet, carefully tap the track back into its appropriate position. Make sure it’s precisely straight with a level.
Once you’ve got the alignment right, tighten the screws down hard to keep the track from moving when you open your garage door.
Broken springs
You may have broken torsion springs if your garage door suddenly won’t go up. Even if the transmitters are operating properly and power is getting to the motor.
Garage doors can be quite heavy, and contrary to popular belief, it is the heavy-duty springs of the door that do the hard lifting, not the garage door opener.
Solution
If a spring breaks, have it repaired by an expert, as these can be dangerous to work with. Wait for a professional to inspect the door and replace the springs before attempting to open it.
Springs can only be used for a specific number of open and shut cycles before breaking and needing to replace.
Issues with limit setting
You may notice that your garage door closes completely and then instantly rises again, rather than remaining in the closed position. This problem most commonly occurs with newly installed garage doors or older types that need to be reset.
If it occurs, your garage door openers’ open and close limit settings are most likely to blame. If your door is positioned too high, it will touch the ground before the opener believes it should.
Solution
Depending on the type and kind of garage door you have, the exact placement and resetting processes will differ. More exact instructions on how to alter your restrictions should be found in your owner’s manual.
You may have to try with a few different settings before you find the right one. If altering the limit settings doesn’t work, it’s time to hire a technician to come out and assist you.
Something is blocking the door
Objects, such as garbage cans or toys, can cause your garage door to close partially and then return to its original position. An accumulation of debris on the tracks could also be the culprit, preventing the rollers from moving forward.
If the door touches even a minor object on the track, it will return to its original position to prevent crushing whatever is beneath it.
Solution
Examine the area around your garage door to see whether the photo eye sensors are blocked. Then take a check within the tracks to see if there is any build up.
View the tracks on the top half of your garage from ground level, with the help of acquiring a step ladder.
Conclusion
To conclude, automatic garage doors are critical to a home’s safety and security. If you’re leaving your house quickly, it’s a must. You operate your device by pressing a button. The door would close on its own.
It gives homeowners peace of mind when they return home from work. However, there are situations when the door opener fails. Whether it’s a garage door or an automatic sliding door. Problems do occur with time and continuous usage.
Perhaps, you should run a timely check to see if your doors are functioning properly. Or why not take the help from professionals, who can provide services and cleaning to your doors,
